The properties of the ISensor class are listed here.
|  | 
Name  | 
Description  | 
|   | 
Defines in minutes the interval at which the sensor communicates with the gateway when the sensor is in the aware state. Unless triggered to communicate earlier, the sensor will send a data message to the gateway when this many minutes elapse.   | |
|   | 
For trigger based sensors (Open/Closed, Water, etc) Determines if the sensor is bistable (triggers both directions) or monostable (triggers one direction)   | |
|   | 
For interval based sensors (Temperature, Humidity, etc) Value used by profiles for calibration   | |
|   | 
For interval based sensors (Temperature, Humidity, etc) Value used by profiles for calibration   | |
|   | 
For interval based sensors (Temperature, Humidity, etc) Value used by profiles for calibration   | |
|   | 
For interval based sensors (Temperature, Humidity, etc) Value used by profiles for calibration   | |
|   | 
For Wi-Fi sensors Determines whether to use short term logging or long term data logging on the sensor when Wi-Fi connection is not available   | |
|   | 
For trigger based sensors (Open/Closed, Water, etc) Sets the event count that must be breached to trigger the event   | |
|   | 
For trigger based sensors (Open/Closed, Water, etc) Sets the time period in ms that the event detection count to increment before it is reset   | |
|   | 
For trigger based sensors (Open/Closed, Water, etc) Determines if the sensor is normally open or normally closed, the other state triggering aware   | |
|   | 
Tracks the version of firmware. Some features are only available on certain firmware versions.   | |
|   | 
If set this flag will cause the General Config 2 page to be sent to the sensor Affected Fields: Recovery, RetryCount   | |
|   | 
If set this flag will cause the General Config 1 page to be sent to the sensor Affected Fields: Report Interval, ActiveStateInterval, TransmitIntervalLink   | |
|   | 
The value of which firmware generation the sensor belongs to ie GEN1, GEN2, WIFI   | |
|   | 
For interval based sensors (Temperature, Humidity, etc) When leaving aware mode back into standard mode the sensor reading must clear the Max or Min threshold by this amount.   | |
|   | 
For interval based sensors (Temperature, Humidity, etc) If reading is above this value the sensor enters aware mode   | |
|   | 
For interval based sensors (Temperature, Humidity, etc) Sets often between report intervals the sensors samples against thresholds   | |
|   | 
For interval based sensors (Temperature, Humidity, etc) If reading is below this value the sensor enters aware mode   | |
|   | 
If set this flag will cause the action control command will be sent to the sensor   | |
|   | 
If set this flag will cause the Profile Config 2 page to be sent to the sensor Affected Fields (Interval): Calibration1, Calibration2, Calibration3, Calibration4   | |
|   | 
If set this flag will cause the Profile Config 1 page to be sent to the sensor Affected Fields (Interval): MeasurementsPerTransmission, MaximumThreshold, MinimumThreshold, Hysteresis Affected Fields (Trigger): EventDetectionCount, EventDetectionPeriod, EventDetectionType, BiStable, RearmTime   | |
|   | 
For trigger based sensors (Open/Closed, Water, etc) sets the amount of time before a bistable trigger is reset to observe another event   | |
|   | 
Defines the number of failed transmission sets before entering link mode   | |
|   | 
Defines in minutes the interval at which the sensor communicates with the gateway. Unless triggered to communicate earlier, the sensor will send a data message to the gateway when this many minutes elapse.   | |
|   | 
Defines the number of back to back attempts in a transmission set   | |
|   | 
Unique numeric identifier of the sensor.   | |
|   | 
Sets the time between link attempts in link mode. Default: 2   | 
| 
Copyright (c) 2017. All rights reserved. | 
| 
What do you think about this topic? Send feedback! |