Name 

Description 

 

ApplicationProfileType 

description of the sensor type if it is triggered or interval based  

 

FirmwareVersion 

The firmware of the sensor  

 

GeneralConfig1Dirty 

set when the ReportInterval, ActiveStateInterval or TransmitIntervalLink  

 

GeneralConfig2Dirty 

set when Recovery is changed  

 

MonnitApplication 

the type of sensor being used such as temperature or humidity  

 

Recovery 

Once the recovery count is reached, the sensor will go to link mode and begin scanning channels and trying to find a gateway to join  

 

ReportInterval 

how often the sensor will send non aware data to a gateway  

 

RetryCount 

How many times recovery should happen  

 

SensorID 

the unique sensor identifier  

 

TransmitIntervalLink 

How often the sensor attempts to re-link with a gateway once it goes into link mode. Values below 12 are interpreted as hours. values above 12 are interpreted as minutes. the max value allowed in this field is 250. if a value of 0 is given the sensor will default to a re-link interval of 2 hours  

 

Name 

Description 

 

Sensor 

This is the overview for the Sensor constructor overload. 

 

Name 

Description 

 

addActionControlCommand 

this is now handled by the sensors base application class
 

 

BatteryPercentageHelper 

This is the overview for the BatteryPercentageHelper method overload. 

 

ForceConfiguration 

 

 

getActionControlCommandIsUrgent 

gets if acc has been set for the sensor  

 

getActionControlCommands 

this is now handled by the sensors base application class
 

 

getActiveStateInterval 

gets the aware state heartbeat for the sensor  

 

getBiStable 

gets what the bistable value has been set as  

 

getCalibration1 

gets calibration 1 value  

 

getCalibration2 

gets calibration 2 value  

 

getCalibration3 

gets calibration 3 value  

 

getCalibration4 

gets calibration 4 value  

 

getDataLog 

 

 

getEventDetectionCount 

gets the event detection count  

 

getEventDetectionPeriod 

gets event detection period  

 

getEventDetectionType 

gets the type of event that will put the trigger sensor in aware  

 

getFirmwareVersion 

gets the firmware version for the sensor  

 

getGeneralConfig1Dirty 

gets if update should take place  

 

getGeneralConfig2Dirty 

gets if general config 2 values should be updated or not.  

 

getHysteresis 

gets the hysteresis value  

 

getMaximumThreshold 

gets the maximum aware threshold  

 

getMeasurementsPerTransmission 

gets how many times during a report interval the sensor will take a measurement  

 

getMinimumThreshold 

gets the minimum aware threshold  

 

getMonnitApplication 

gets the application profile type of the sensor  

 

getPendingActionControlCommand 

gets if pending action control command has been set  

 

getProfileConfig1Dirty 

gets if there needs to be an update  

 

getProfileConfig2Dirty 

lets you know if calibration 1 through 4 has been changed  

 

getRearmTime 

get how long in seconds it take to allow a trigger type sensor to be able to be re-triggered  

 

getRecovery 

gets the value that should be reached before link mode  

 

getReportInterval 

gets the normal heartbeat for the sensor  

 

getRetryCount 

gets how many times the sensor will attempt to reconnect to the gateway  

 

getSensorID 

gets the sensors unique identifier  

 

getTransmitIntervalLink 

gets How often the sensor attempts to re-link with a gateway once it goes into link mode. Values below 12 are interpreted as hours. values above 12 are interpreted as minutes. the max value allowed in this field is 250. if a value of 0 is given the sensor will default to a re-link interval of 2 hours  

 

MarkClean 

marks all flags for update false  

 

ReadConfigCommand 

this is now handled by the sensors base application class
 

 

removeActionControlCommands 

this is now handled by the sensors base application class
 

 

setActionControlCommandIsUrgent 

sets the action control command
 

 

setActionControlCommands 

this is now handled by the sensors base application class
 

 

setActiveStateInterval 

sets the aware state heartbeat for the sensor
 

 

setBiStable 

If Aware Reading is selected, then the time between the message detecting motion and the message saying 'no motion' is (rearm time + aware state heartbeat). If set to All State Changes, then the time between the two messages is (rearm time + rearm time).This example assumes standard Aware on Motion state.
 

 

setCalibration1 

sets calibration 1
 

 

setCalibration2 

sets calibration 2
 

 

setCalibration3 

sets calibration 3
 

 

setCalibration4 

sets calibration 4
 

 

setDataLog 

 

 

setEventDetectionCount 

determine by sensor type
 

 

setEventDetectionPeriod 

determined by sensor type
 

 

setEventDetectionType 

sets which reading of the sensor will trigger the aware state for trigger sensors
 

 

setGeneralConfig1Dirty 

sets if general config 1 values should be updated
 

 

setGeneralConfig2Dirty 

sets if GeneralConfig2Dirty values should be updated
 

 

setHysteresis 

A buffer to prevent the sensor from bouncing between standard operation and aware state when the assessments are very close to a threshold. for example, if a maximum threshold is set to 90 degrees and a hysteresis of 1 degree, then once the sensor takes an assessment of 90.0 degrees and enters the aware state it will remain in the aware state until the temperature readings drop to 89.0 degrees
 

 

setMaximumThreshold 

sets the maximum threshold of the aware state
 

 

setMeasurementsPerTransmission 

sets how many times during the heartbeat a measurement should be taken an example would be if you have a 10 minute reportinterval and you set this value to 2 every 5 minutes a measurement will be taken and if it is in the aware state it will send the data out otherwise it will wait until the report interval to be met to send the data to the gateway.
 

 

setMinimumThreshold 

sets the minimum threshold of the aware state
 

 

setPendingActionControlCommand 

allows you to set pending action control command
 

 

setProfileConfig1Dirty 

allows you to set this value to true if specific values you need to updated  

 

setProfileConfig2Dirty 

set to true if any calibration 1 through 4 has been changed
 

 

setRearmTime 

set how long in seconds it take to allow a trigger type sensor to be able to be re-triggered  

 

setRecovery 

Once the recovery count is reached, the sensor will go to link mode and begin scanning channels and trying to find a gateway to join
 

 

setRetryCount 

sets the retry count on the sensor
 

 

UpdateLinkInterval 

this is now handled by the sensors base application class
 

 

UpdateRecoveryCount 

this is now handled by the sensors base application class
 

 

UpdateReportInterval 

this is now handled by the sensors base application class
 

 

UpdateRetryCount 

this is now handled by the sensors base application class