Name 

Description 

 

ConfigSection 

Used to fill the byte array with the proper values to send a configuration page to the sensor  

 

FillConfig 

used to fill sensor values with the proper values from the byte array to sent from the sensor  

 

ReadConfigCommand 

Builds the command used to ask the sensor to send a copy of it's configuration page  

 

Name 

Description 

 

BatteryPercentageHelper 

This is the overview for the BatteryPercentageHelper method overload. 

 

ForceConfiguration 

Force server held configurations to be sent to the sensor at the next communication cycle.  

 

LinearInterpolation 

This is LinearInterpolation, a member of class Sensor. 

 

Sensor 

This is the overview for the Sensor constructor overload. 

 

UpdateLinkInterval 

Defines in minutes the interval at which the sensor attempts to link/re-link with the gateway. Link heartbeats greater than 1 hour will be rounded to the nearest hour. Accepted values between 1 and 720 (1 minute to 12 hours)  

 

UpdateRecoveryCount 

Sets number of messages sensor sends without acknowledgment from gateway before entering link mode Accepted values between 0 and 10 0 means unlimited (no self healing, power cycling senor will be required if gateway changes channel)  

 

UpdateReportInterval 

Defines in minutes the interval at which the sensor communicates with the gateway. Unless triggered to communicate earlier, the sensor will send a data message to the gateway when this many minutes elapse. Accepted values between .017 and 720 (1 second to 12 hours)  

 

UpdateRetryCount 

Sets number of RF packets sensor attempts to send a single message to gateway. Accepted values between 0 and 10  

Name 

Description 

Sensor.ActionControlCommandIsUrgent 

The action control command that will be sent to the sensor is urgent  

Sensor.ActionControlCommands 

The action control command(s) that will be sent to the sensor  

Sensor.ActiveStateInterval 

Defines in minutes the interval at which the sensor communicates with the gateway when the sensor is in the aware state. Unless triggered to communicate earlier, the sensor will send a data message to the gateway when this many minutes elapse.  

Sensor.BiStable 

For trigger based sensors (Open/Closed, Water, etc) Determines if the sensor is bistable (triggers both directions) or monostable (triggers one direction)  

Sensor.Calibration1 

For interval based sensors (Temperature, Humidity, etc) Value used by profiles for calibration  

Sensor.Calibration2 

For interval based sensors (Temperature, Humidity, etc) Value used by profiles for calibration  

Sensor.Calibration3 

For interval based sensors (Temperature, Humidity, etc) Value used by profiles for calibration  

Sensor.Calibration4 

For interval based sensors (Temperature, Humidity, etc) Value used by profiles for calibration  

Sensor.DataLog 

For Wi-Fi sensors Determines whether to use short term logging or long term data logging on the sensor when Wi-Fi connection is not available  

Sensor.EventDetectionCount 

For trigger based sensors (Open/Closed, Water, etc) Sets the event count that must be breached to trigger the event  

Sensor.EventDetectionPeriod 

For trigger based sensors (Open/Closed, Water, etc) Sets the time period in ms that the event detection count to increment before it is reset  

Sensor.EventDetectionType 

For trigger based sensors (Open/Closed, Water, etc) Determines if the sensor is normally open or normally closed, the other state triggering aware  

Sensor.FirmwareVersion 

Tracks the version of firmware. Some features are only available on certain firmware versions.  

Sensor.GeneralConfig2Dirty 

If set this flag will cause the General Config 2 page to be sent to the sensor Affected Fields: Recovery, RetryCount  

Sensor.GeneralConfigDirty 

If set this flag will cause the General Config 1 page to be sent to the sensor Affected Fields: Report Interval, ActiveStateInterval, TransmitIntervalLink  

Sensor.GenerationType 

The value of which firmware generation the sensor belongs to ie GEN1, GEN2, WIFI  

Sensor.Hysteresis 

For interval based sensors (Temperature, Humidity, etc) When leaving aware mode back into standard mode the sensor reading must clear the Max or Min threshold by this amount.  

Sensor.MaximumThreshold 

For interval based sensors (Temperature, Humidity, etc) If reading is above this value the sensor enters aware mode  

Sensor.MeasurementsPerTransmission 

For interval based sensors (Temperature, Humidity, etc) Sets often between report intervals the sensors samples against thresholds  

Sensor.MinimumThreshold 

For interval based sensors (Temperature, Humidity, etc) If reading is below this value the sensor enters aware mode  

Sensor.MonnitApplication 

Identifier of the sensor application type. (Temp/Humidity/etc)  

Sensor.PendingActionControlCommand 

If set this flag will cause the action control command will be sent to the sensor  

Sensor.ProfileConfig2Dirty 

If set this flag will cause the Profile Config 2 page to be sent to the sensor Affected Fields (Interval): Calibration1, Calibration2, Calibration3, Calibration4  

Sensor.ProfileConfigDirty 

If set this flag will cause the Profile Config 1 page to be sent to the sensor Affected Fields (Interval): MeasurementsPerTransmission, MaximumThreshold, MinimumThreshold, Hysteresis Affected Fields (Trigger): EventDetectionCount, EventDetectionPeriod, EventDetectionType, BiStable, RearmTime  

Sensor.RearmTime 

For trigger based sensors (Open/Closed, Water, etc) sets the amount of time before a bistable trigger is reset to observe another event  

Sensor.Recovery 

Defines the number of failed transmission sets before entering link mode  

Sensor.ReportInterval 

Defines in minutes the interval at which the sensor communicates with the gateway. Unless triggered to communicate earlier, the sensor will send a data message to the gateway when this many minutes elapse.  

Sensor.RetryCount 

Defines the number of back to back attempts in a transmission set  

Sensor.SensorID 

Unique numeric identifier of the sensor.  

Sensor.TransmitIntervalLink 

Sets the time between link attempts in link mode. Default: 2