Name 

Description 

 

ConfigSection 

Used to fill the byte array with the proper values to send a configuration page to the sensor  

 

FillConfig 

used to fill sensor values with the proper values from the byte array to sent from the sensor  

 

ReadConfigCommand 

Builds the command used to ask the sensor to send a copy of it's configuration page  

 

Name 

Description 

 

_ActionControlCommands 

This is _ActionControlCommands, a member of class Sensor. 

 

Name 

Description 

 

BiStable 

For trigger based sensors (Open/Closed, Water, etc) Determines if the sensor is bistable (triggers both directions) or monostable (triggers one direction)  

 

Calibration1 

For interval based sensors (Temperature, Humidity, etc) Value used by profiles for calibration  

 

Calibration2 

For interval based sensors (Temperature, Humidity, etc) Value used by profiles for calibration  

 

Calibration3 

For interval based sensors (Temperature, Humidity, etc) Value used by profiles for calibration  

 

Calibration4 

For interval based sensors (Temperature, Humidity, etc) Value used by profiles for calibration  

 

DataLog 

For Wi-Fi sensors Determines whether to use short term logging or long term data logging on the sensor when Wi-Fi connection is not available  

 

EventDetectionCount 

For trigger based sensors (Open/Closed, Water, etc) Sets the event count that must be breached to trigger the event  

 

EventDetectionPeriod 

For trigger based sensors (Open/Closed, Water, etc) Sets the time period in ms that the event detection count to increment before it is reset  

 

EventDetectionType 

For trigger based sensors (Open/Closed, Water, etc) Determines if the sensor is normally open or normally closed, the other state triggering aware  

 

Hysteresis 

For interval based sensors (Temperature, Humidity, etc) When leaving aware mode back into standard mode the sensor reading must clear the Max or Min threshold by this amount.  

 

MaximumThreshold 

For interval based sensors (Temperature, Humidity, etc) If reading is above this value the sensor enters aware mode  

 

MeasurementsPerTransmission 

For interval based sensors (Temperature, Humidity, etc) Sets often between report intervals the sensors samples against thresholds  

 

RearmTime 

For trigger based sensors (Open/Closed, Water, etc) sets the amount of time before a bistable trigger is reset to observe another event  

 

Name 

Description 

 

BatteryPercentageHelper 

This is the overview for the BatteryPercentageHelper method overload. 

 

ForceConfiguration 

Force server held configurations to be sent to the sensor at the next communication cycle.  

 

Sensor 

This is the overview for the Sensor constructor overload. 

 

UpdateLinkInterval 

Defines in minutes the interval at which the sensor attempts to link/re-link with the gateway. Link heartbeats greater than 1 hour will be rounded to the nearest hour. Accepted values between 1 and 720 (1 minute to 12 hours)  

 

UpdateRecoveryCount 

Sets number of messages sensor sends without acknowledgment from gateway before entering link mode Accepted values between 0 and 10 0 means unlimited (no self healing, power cycling senor will be required if gateway changes channel)  

 

UpdateReportInterval 

Defines in minutes the interval at which the sensor communicates with the gateway. Unless triggered to communicate earlier, the sensor will send a data message to the gateway when this many minutes elapse. Accepted values between .017 and 720 (1 second to 12 hours)  

 

UpdateRetryCount 

Sets number of RF packets sensor attempts to send a single message to gateway. Accepted values between 0 and 10  

 

Name 

Description 

 

ActionControlCommandIsUrgent 

The action control command that will be sent to the sensor is urgent  

 

ActionControlCommands 

The action control command(s) that will be sent to the sensor  

 

ActiveStateInterval 

Defines in minutes the interval at which the sensor communicates with the gateway when the sensor is in the aware state. Unless triggered to communicate earlier, the sensor will send a data message to the gateway when this many minutes elapse.  

 

FirmwareVersion 

Tracks the version of firmware. Some features are only available on certain firmware versions.  

 

GeneralConfig1Dirty 

If set this flag will cause the General Config 1 page to be sent to the sensor Affected Fields: Report Interval, ActiveStateInterval, TransmitIntervalLink  

 

GeneralConfig2Dirty 

If set this flag will cause the General Config 2 page to be sent to the sensor Affected Fields: Recovery, RetryCount  

 

MinimumThreshold 

For interval based sensors (Temperature, Humidity, etc) If reading is below this value the sensor enters aware mode  

 

MonnitApplication 

Identifier of the sensor application type. (Temp/Humidity/etc)  

 

PendingActionControlCommand 

If set this flag will cause the action control command will be sent to the sensor  

 

ProfileConfig1Dirty 

If set this flag will cause the Profile Config 1 page to be sent to the sensor Affected Fields (Interval): MeasurementsPerTransmission, MaximumThreshold, MinimumThreshold, Hysteresis Affected Fields (Trigger): EventDetectionCount, EventDetectionPeriod, EventDetectionType, BiStable, RearmTime  

 

ProfileConfig2Dirty 

If set this flag will cause the Profile Config 2 page to be sent to the sensor Affected Fields (Interval): Calibration1, Calibration2, Calibration3, Calibration4  

 

Recovery 

Defines the number of failed transmission sets before entering link mode  

 

ReportInterval 

Defines in minutes the interval at which the sensor communicates with the gateway. Unless triggered to communicate earlier, the sensor will send a data message to the gateway when this many minutes elapse.  

 

RetryCount 

Defines the number of back to back attempts in a transmission set  

 

SensorID 

Unique numeric identifier of the sensor.  

 

TransmitIntervalLink 

Sets the time between link attempts in link mode. Default: 2